Design House 546184 Bedienerhandbuch PDF herunterladen

Your new Design House faucet will give you years of trouble free performance. Thank you for

choosing our product for your home. Please read all of these instructions carefully before

installing your new faucet.

When installing your new faucet, hand tighten the connector nuts, then use one wrench to

anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that

are too tight will reduce the integrity of the system.

Wrap threaded connections (except aerator thread in spout or where o-ring or rubber sealant

are present) with Teflon tape available from your local hardware or plumbing supply store.

Always wrap in a clockwise direction.

IMPORTANT POINTS

SAFETY TIPS

ALWAYS protect your eyes with safety glasses.

Helpful tools to install this faucet:

Teflon tape

(2) crescent wrenches

basin wrench

flashlight

faucet supply tubes

silicon sealer

6.SHOWER FLANGE, SHOWER ARM

AND SHOWER HEAD INSTALLATION

Insert the long end of the shower arm (6A)

through the flange (6B), then wrap thread

sealant tape around the long end of the

shower arm (6A) in a clockwise direction,

as shown. Install the long end of the

shower arm (6A) into the pipe elbow inside

the wall. The flange (6B) should fit snug to

the finished wall surface. Thread the

shower head (6C) onto the shower arm

(6A). Carefully tighten the shower arm (6A)

and shower head (6C). Do not over tighten,

as it could cause damage to the shower

arm (6A).

5.FLUSHING

For tub and shower combinations:

Turn on the hot and cold water supply

lines, allowing water to flow from the tub

spout outlet (5A, not included) until all

debris is cleared from the line. Check all

connections for leaks.

For shower only combinations:

Turn on the hot and cold water supply

lines, allowing water to flow from the

shower outlet (5B, not included) until all

debris is cleared from the line. Pressure

must be approximately equal on both hot

and cold sides for the valve to function

properly. Check all connections for leaks.

4.SHOWER ONLY OUTLET

CONNECTIONS

Wrap thread sealant tape around the pipe

threads in a clockwise direction, as

shown. Connect the shower outlet pipe

(4A, not included) to valve body (4B).

Wrap thread sealant tape around the

threads of the plug (4C), and insert it into

the bottom outlet (4D). Connect the pipe

elbows (4E, not included) to the end of

the pipe, and tighten with a wrench.

1.Shut off the water supply to the tub and

shower. Verify that the hole sizes and

position in the wall are correct:

A. The shower and tub spout outlet holes

should be 1-1/4 in. diameter.

B. For the cold water inlet (the right side) and

the hot water inlet (the left side), cut or leave

a 1-3/8 in. diameter hole (recommended size

is 1-3/4 in.). The center to center distance

between the cold and hot water inlets is 8 in.

Note: Do not disassemble the cartridges

during normal installation. When reinstalling

the cartridge, be sure to insert with the limit

stop (a & b) pointed inward as shown in the

diagram. This is necessary for proper

operation of the valve.

2.SUPPLY CONNECTION LAYOUT

Wrap thread sealant tape around the

valve body (2A) threads in a clockwise

direction, as shown. Thread the waterline

(2B, not included) to the valve body (2A),

and tighten with a wrench.

Note: a. Be sure to position the body (2A)

correctly in the wall, with the markings

"UP" facing upward.

b. Hot water supply lines go into the

H inlet, cold water supply lines go into the

C inlet.

3.TUB & SHOWER OUTLET

CONNECTIONS

Wrap thread sealant tape around the pipe

threads in a clockwise direction, as shown.

Connect the shower (3A, not included) and

tub outlet pipes (3B, not included) to the

valve body (3C). Connect the pipe elbows

(3D, not included) to the ends of both pipes,

and tighten with a wrench.

Note: Do not use PEX or CPVC between the

valve and spout.

8 in.

48 in.

Shower Only

30 in.

Tub & Shower

48 in.

Tub & Shower

30 in.

Shower Only

8 in. Min.

1-3/8 in. ~ 2 in.

Cold

Hot

Tub

Shower

1-3/8 in. ~ 2 in.

1 2

Inhaltsverzeichnis

Seite 1 - SAFETY TIPS

Your new Design House faucet will give you years of trouble free performance. Thank you forchoosing our product for your home. Please read all of thes

Seite 2 - CONSUMER PROTECTION WARNING

o 546184 - Polished Chrome7.FOR TUB SPOUT INSTALLATIONWrap thread sealant tape around the pipe threads ofthe tub spout outlet (7A, not included) in

Kommentare zu diesen Handbüchern

Keine Kommentare

Design House 546184 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Sanitärkeramik Design House 546184 herunter. Design House 546184 Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sanitärkeramik Design House 546184